ANSI C82.3-1983 R1995
|
ID： |
57D79387EC37486D833BCB1E56402CCF |
|
文件大小(MB)： |
1.04 |
|
页数： |
20 |
|
文件格式： |
|
|
日期： |
2007-12-7 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
for reference ballasts,for fluorescent lamps,--`,,,``,,``,,,`,,,``,,`,,`-`-`,,`,,`,`,,`---,A N S I C82.3 83 W 072Ll150 O006137 2 W,ANSI @,C82.3- 1983,Revision of,ANSI C82.3-1977,American National Standard,for Reference Ballasts,for Fluorescent Lamps,Secretariat,National Electrical Manufacturers Association,Approved May 16,1983,American National Standards Institute, Inc,--`,,,``,,``,,,`,,,``,,`,,`-`-`,,`,,`,`,,`---,American An American National Standard implies a consensus of those substantially concerned with its,scope and provisions. An American National Standard is intended as a guide to aid the manu- National facturer, the consumer, and the general public. The existence of an American National Standard,does not in any respect preclude anyone, whether he has approved the standard or not, Standard from manufacturing, marketing, purchasing, or using products, processes, or procedures not,conforming to the standard, American National Standards are subject to periodic review and,users are cautioned to obtain the latest editions.,Published by,American National Standards Institute,1430 Broadway, New York, New York 10018,Copyright O 1983 by American National Standards Institute, Inc,All rights reserved.,No part of this publication may be reproduced in any form,in an electronic retrieval system or otherwise, without,the prior written permission of the publisher.,The American National Standards Institute does not develop standards and will in no circumstances,give an interpretation of any American National Standard. Moreover, no person shall,have the right or authority to issue an interprefation of an American National Standard in the,name of the American National Standards Institute.,CAUTION NOTICE: This American National Standard may be revised or withdrawn at any,t h e . The procedures of the American National Standards Institute require that action be,taken to reaffirm, revise, or withdraw this standard no later than five years from the date,of approval. Purchasers of American National Standards may receive current information,on all standards by calling or writing the American National Standards Institute.,Printed in the United States of America,A頜S83/6,--`,,,``,,``,,,`,,,``,,`,,`-`-`,,`,,`,`,,`---,Foreword (This Foreword is not part of American National Standard C82.3-1983.),In order to obtain satisfactory performance of fluorescent lamps and their associated ballasts,it is necessary that certain features of their designs be properly coordinated. Specifications,for the operation of either the lamps or the ballasts must naturally be written in,terms of measurements made against some common baseline of reference.,Because of the inherent instability of gaseous discharge lamps, experience has shown them,to be unsuited as a reference..A ballast, however, can be specially designed to provide a,reasonably permanent and reproducible baseline for measurements. Such ballasts are designated,as reference ballasts, This standard describes those characteristics that have been,found necessary in ballasts to ensure permanence and reproducibility.,This standard was originally published for tría1 and criticism in 1950 and again in 1953.,It was first approved as an American National Standard in 1956. Subsequent editions,were published in 1957, 1962, 1972, and 1977.,Dimensions in this standard are given in inches; millimeter conversions are given in,parentheses and have been rounded.,Suggestions for improvements of this standard will be welcome. They should be sent to,the National Electrical Manufacturers Association, 2101 L Street, NW, Washington, D.C.,20037,This standard was processed and approved for submittal to ANSI by American National,Standards Committee on Lamp Ballasts, C82. Committee approval of the standard does,not necessarily imply that all committee members voted for its approval. At the time it,approved this standard, the C82 Committee had the following members:,Anton Franke, Chair,Fred P. Smith, Secretary,Organization Represented,AdvanceTransformerCompany. ..,Duro-TestCorporafion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .,ETLTestingLaboratories, Inc.,General Electric Company. ..,General Services Administration ..,GTE Products Corporation ..,Institute of Electrical and Electronics Engineers . . . . . . . . . . . . . . . . .,National Electrical Manufacturers Association . . . . . . . . . . . . . . . . . .,OSRAMSaIesCorporation. . . . . . . . . . . . . . L . . . . . . . . . . . . . . .,North American Philips Lighting Corporation. . . . . . . . . . . . . . . . . . .,Telephone Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .,Universal Ma……
……